![]() This document helps to adjust he timeout to a value which is appropriate for most situations. HTTP/3 uses QUIC instead of TCP for the underlying transport protocol. However, in some circumstances, applying a Cumulative Release patch to Portal may take longer than a minute, causing Apache to rise a transport error, which leads to a patch operation failure. The Hypertext Transfer Protocol (HTTP) is an application layer protocol in the Internet. DWORD 0x00000000 or Not Present negotiate NLA using TLS. This value, defines the amount of time that the services waits for receipts and transmissions during communications. Simplicity comes at a price, however, in this case, DNS round robin isn't truly load-balancing the traffic, because there isn't a way programmatically to make sure that each server gets a fair share of the traffic. The embedded Apache HTTP service has a "timeout" value in its configuration file that is set (out of the box) to 60 seconds. The HTTP client is smart enough to connect to another server should one Exchange server fail completely. This usually happens when the patch routine process takes longer than what the HTTP services is willing to wait. ClientProtocolException: Unexpected response status: 502Īt com.ca.$1.handleResponse(CMSClient.java:45)Īt com.ca.$1.handleResponse(CMSClient.java:1)Īt .(CloseableHttpClient.java:218)Īt .(CloseableHttpClient.java:160)Īt .(CloseableHttpClient.java:136)Īt com.ca.(CMSClient.java:153 Skipping patch v3.5.CR7-content.cmspatch already appliedįatal transport error: Unexpected response status: 502 Skipping patch v3.5.CR6-phrases.cmspatch already applied Skipping patch v3.5.CR4-phrases.cmspatch already applied Skipping patch v3.5.CR3-content.cmspatch already applied Skipping patch v3.5.CR3-phrases.cmspatch already applied Skipping patch v3.5.CR2-phrases.cmspatch already applied 4 says: Client software SHOULD reopen the transport connection and retransmit the aborted sequence of requests without user interaction so long as the request. Skipping patch v3.5.CR1-phrases.cmspatch already applied Waiting for catalina to start, please be patient. A protocol used by the client that isn’t supported by the server. Some server-side causes include: A cipher suite mismatch. A connection that is being intercepted by a third party. If it is, then I would try running the BES Remove Utility to completely remove the relay, restart the BES Client service, wait for the client to reconnect to another relay, then re-install the relay via fixlet.The following error may be experienced while applying a Cumulative Release (CR) onto Portal 3.5 Common causes of SSL errors on the client-side include: The wrong date or time on the client device. I would probably start by double checking that TLS 1.2 is enabled on the relay server. Could be something else wrong with the relay configuration. Now the fact that the relay is also not reporting in (if I am reading your first post correctly) would point to the fact that it’s the relay that is the issue.Ĭould be TLS 1.2 is not enabled on the relay (I have seen this cause very similar issues) so it can’t communicate with clients, other relays, or root. This can be useful if you want to try uninstalling/re-installing the relay via fixlets.īasically the “client on the relay is not registering with a relay” issue is not a network issue. You may need to restart the BES Client service as well, if just to speed things up. ![]() If you need to reconnect to the client, you can stop the relay service and then the client will revert to normal relay selection and find another relay. It will do this no matter what relay selection method you have told the client to use. ![]() If a relay service is running on the same computer as a client the client will always try to use the relay running on the same computer via the loopback address. The client on the relay is trying to connect to 127.0.0.1, which is the loopback address. Abstracts away the underlying HTTP transport, allowing you to write environment and transport agnostic code i.e., no hard dependency on cURL, PHP streams.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |